Baseboards video compilations

Installing Baseboard Trim
Posted by: HomeAdditionPlus

Video duration: 240 seconds
Global video hits: 205540

Mark Donovan of HomeAdditionPlus.com steps through the process of removing and installing baseboard trim.

Related: installing, baseboard, trim

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

I would suggest ...
By: HomeAdditionPlus. on 17 Apr 12, 10:17:48
I would suggest going with a 16 gauge finished nailer.?

do i need a 18 ...
By: okrabay. on 17 Apr 12, 03:22:00
do i need a 18 gauge brad nailer or? a finish nailer?

Thanks?
By: 1973bugml. on 07 Mar 12, 20:57:59
Thanks?

I installed nails? ...
By: HomeAdditionPlus. on 21 Feb 12, 23:11:09
I installed nails? every 16 inches which is the standard wall stud separation. I used a paintable latex caulk. Wood filler would also work well, and yes you could sand and paint it.

how far apart did ...
By: ninjaryder1st. on 21 Feb 12, 16:41:58
how far apart did you nail in your brads? 12? inches? and what kind of caulk material did you use? silicone, or other, water proof? could you use wood filler rather than caulk over the nail holes, sand and paint?

Edf1956, yes I too ...
By: ptcpaul. on 05 Feb 12, 20:36:09
Edf1956, yes I too would repair, but also would move door stop to top of door, as he says in video someone stepped on it, I can see that happening sgain. Also I would paint it first then install and touch up, you nitice he never touches bottom of? trim with brush

You can buy a mitre ...
By: karerer. on 28 Aug 11, 18:38:06
You can buy a mitre box and saw for? about $20-25.

Nice job on the ...
By: ECF1956. on 12 Jul 11, 12:01:42
Nice job on the instructional video. But in this case I would go? for a repair rather than replacement since it is painted. Just clean out the damage, fill in with a bit of bondo, sand after it dries, and paint. Replace the door stop and move it outside the damaged area. Much less work and the results are the same or better.

It looks easy to do ...
By: vgrandja. on 29 May 11, 21:01:52
It looks easy to do for a novice. I don't have an electric saw, though. Maybe if I had? the correct measurements, Home Depot can cut the baseboards for me. Using caulk to cover the nails,..thanks for this tidbit.

thanks ?
By: oker83. on 28 May 11, 04:34:25
thanks ?

very? heelpful!
By: lovebaby861. on 08 May 11, 22:53:03
very? heelpful!

backer? rod
By: BigEMU1. on 13 Mar 11, 01:13:17
backer? rod

Thank you very much ...
By: mlcatoe. on 01 Mar 11, 06:13:00
Thank you very much for? this practical and simple explanation of replacing the trim. I have subscribed to HomeAdditionPlus and look forward to more videos soon. mlc

You could consider ...
By: HomeAdditionPlus. on 18 Jan 11, 00:46:29
You could consider adding quarter-round to? the bottom edge of the baseboard trim.

How do I fill the ...
By: mckubik. on 18 Jan 11, 00:17:46
How do I fill the gap between the baseboard and tile, when several tiles are lower than the others. Most of the gap is 1/8 inch, which can be caulked, but how do I fill bigger 1/4" gaps??

Awesome video. ...
By: SportySardar. on 29 Aug 10, 17:07:13
Awesome video. Thanks for uploading.?

Just remember to ...
By: mikenew403. on 19 Jun 10, 11:13:50
Just remember to use caulk that you can? paint over. Some caulk is not paint-able.

So helpful, thank ...
By: alisonmann. on 13 Jun 10, 17:40:08
So helpful, thank you! alison from Toronto?

Thanx 4 uploading ...
By: mywatergrass. on 05 May 10, 06:18:33
Thanx 4 uploading it!?

I would consider ...
By: HomeAdditionPlus. on 04 Apr 10, 10:07:01
I would consider using an adhesive or a flexible vinyle? baseboard trim with an adhesive, simliar to what you might see in a commercial application.

Thank you very much ...
By: zgele77. on 04 Apr 10, 04:49:13
Thank you very much for the video The issue I have is that my wall is a concrete (double brick). How do I? fix it to the wall, I can't use nails only can I?? Thank you

I? prefer Pine ...
By: HomeAdditionPlus. on 02 Apr 10, 09:06:57
I? prefer Pine baseboard

Great job on the ...
By: billm0066. on 21 Jan 10, 19:22:58
Great job on the video. Do you prefer pine baseboard? or mdf?

Thank? you so much!
By: timewithtascha. on 16 Jan 10, 18:32:37
Thank? you so much!

I would suggest ...
By: HomeAdditionPlus. on 16 Jan 10, 11:54:05
I would suggest painting the walls after your remove the old baseboard. I? would also suggest painting or staining the new baseboard trim prior to installing. Then all you need to to do is touch up the nail holes after installing and run a bead of caulk.

Home Repair : How to Install Baseboards
Posted by: expertvillage

Video duration: 150 seconds
Global video hits: 51447

Install baseboards after measuring the wall area and cutting the baseboard to fit. Learn how to install baseboards using the home repair tips in this free video. Expert: Ryan Parker Contact: www.ParkerHomeRenova tions.com Bio: Ryan Parker is the owner of Parker Home Renovations in New Braunfels, TX. Filmmaker: Todd Green

Related: home remodeling, home repair, remodeling, building, diy, diy projects, home repair tips

Display Video Comments | Hide Video Comments | Add Comment

DIY tips: Caulking baseboards
Posted by: starksilvercreek

Video duration: 315 seconds
Global video hits: 45318

How to caulk baseboards. Loni shows a simple technique using tape to ensure clean, finished lines for a professional look. www.starkinsider.com

Related: diy, home improvement, caulking, baseboards, renovation, home, flooring, trim, starksilvercreek, how to, loni kao stark, hgtv, baseboard, caulk, bead, home depot

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

She has an accent.? ...
By: barbershop22. on 18 Apr 12, 16:15:59
She has an accent.? British?

Very good. This ...
By: motzingw. on 14 Mar 12, 20:09:33
Very good. This technique allows you to use silicone caulk? -- normally almost impossible to clean of tops of baseboard and walls. Thank you.

What a waste of ...
By: pompeyjames. on 01 Feb 12, 18:14:13
What a waste of time taping? it

...People who dont ...
By: PeckhamExile. on 01 Feb 12, 17:01:22
...People who dont know what they are doing of, or have never done it before maybe??

Pause at 3:55 ! She ...
By: elnatural822. on 14 Jan 12, 19:37:31
Pause at 3:55 ! She pulled? some of the wall off with the tape! Just be neat and smooth with your caulk not sloppy like this lady. A good pointer is never take advise on caulking from someone who sits cross-legged or indian style while doing it!

Great? tip!
By: grannyvonng. on 07 Oct 11, 20:51:33
Great? tip!

I think most of the ...
By: tripjet999. on 20 Aug 11, 13:51:42
I think most of the people posting here could do a better job WITHOUT the tape! I know I could. I have used tape (and blue? painter's tape or the white wallpaper protection tape, not masking tape) for certain applications, but not for baseboards. Keep a damp rag for wetting and wiping your finger and a couple of paper towels for excess.

I think this is her ...
By: ratmq. on 22 Jul 11, 16:01:37
I think this is her first time to the Rodeo?

Could you tell us ...
By: GEK69NY. on 09 Jul 11, 21:33:04
Could you tell us who uses scissors to cut? caulking nozzle?

hell how long I'm ...
By: juan19826. on 22 Jun 11, 02:24:46
hell how long I'm going to take making a House so the best? idea is the finger that is all

this chick doesnt ...
By: KIERNYSTUBE. on 27 Mar 11, 21:11:33
this chick doesnt know wat shes talking about!!! stop wasting time? - no need for tape

This is way too ...
By: nimnestl. on 14 Feb 11, 03:42:47
This is way too much work. Run a bead of caulk, smooth it out with your finger, and keep a damp rag handy to clean up any mess(and for wiping your fingers!). It will look much crisper than this and will fill gaps better, as well. And for crying out loud, buy decent caulk. Don't buy it at the package stores. For this type of application, use something like Sherwin-Williams 850A.? It won't crack later like that crappy DAP will, and it"ll run ya the same price - or even cheaper.

it's? a textured ...
By: eHomeJournal. on 03 Feb 11, 09:53:58
it's? a textured wall

id just lick my ...
By: draconite420. on 05 Dec 10, 17:29:23
id just lick my finger the first time (not with caulk on my finger) than it dont? stick at all to my fingers.

Thanks! But it ...
By: tomax7. on 15 Aug 10, 04:07:12
Thanks! But it still seems 'bumpy' when you took the tape off. Maybe? need to push it more with the finger?

Very easy to follow ...
By: RebelutionHandled. on 22 Mar 10, 16:19:57
Very easy to follow. Thank? you

My experience would ...
By: 4sineweaver2. on 11 Nov 09, 04:51:40
My experience would suggest that this is a great method for textured walls. It's dificult to use the old "wet finger" method to remove caulk from all the little pockets in a textured surface. For smooth surfaces I usually spray a little? Windex on my finger and it makes for a very smooth line.

Very? nice demo, ...
By: MrRofeliak. on 05 Sep 09, 21:33:38
Very? nice demo, thank you.

awesome! excellent ...
By: poiema1006. on 06 Jul 09, 21:03:48
awesome! excellent instruction and very easy to follow. :-) thanks!!!?

Installing Baseboards / Skirting Boards. SECRET REVEALED!
Posted by: shaneconlan1

Video duration: 515 seconds
Global video hits: 38214

Installing baseboard / skirting board: How to cut and install skirting boards / baseboards for a perfect internal corner. Another renovation, remodeling tip from Uncle Knackers www.youtube.com

Related: skirting, boards, base, baseboards, install, install baseboards, how to, skirting boards, carpentry, install skirting boards, fit, diy, coping saw, cope, uncle, knackers, uncle knackers., runmport

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

Ah? mate........ ...
By: jhi1947. on 21 May 12, 17:06:05
Ah? mate........What the fook is a skirting board? Something a lady wears?

u act? ...
By: gringo90100. on 17 May 12, 20:39:06
u act? retarddddddddddddddddddd

never knew the ...
By: IronChefPeter. on 06 May 12, 05:53:27
never knew the crocodile hunter? bid base boards.

crazy work?
By: million8346. on 22 Apr 12, 17:30:47
crazy work?

i always to? the 45 ...
By: Jason52956. on 29 Mar 12, 18:06:46
i always to? the 45 degree angle thing. even after years of practice i still manage to make it look like crap.... but its ok because i work in an office and drink lots of beer.

Love this guy, he's ...
By: TheTopper2010. on 26 Mar 12, 01:32:01
Love this guy, he's very skilled & a great actor!?

Very informative.. ...
By: fjbutch. on 04 Mar 12, 01:40:40
Very informative..well done...?

Good how to video?
By: DownUnderDoug. on 03 Mar 12, 07:08:45
Good how to video?

You are a an? ...
By: BALKINIZED. on 29 Feb 12, 13:20:17
You are a an? Awesome Host Bro...Great Show !!!!! Zulu

wow you made it ...
By: steviejacko. on 28 Feb 12, 09:03:23
wow you made it look so easy? thanks for showing us that great Tip : ) thumbs up

Great Tips? my ...
By: TUCKERZONE. on 28 Feb 12, 06:09:04
Great Tips? my Friend.

Yeah, good stuff. ...
By: sponcombook. on 25 Feb 12, 19:28:04
Yeah, good stuff. Don't forget the wood rasp to clean up and shape the? cuts made with the coping saw - especially on more ornate profiles.

There are two ...
By: shaneconlan1. on 22 Feb 12, 04:17:48
There are two secrets in this video that the everyday DIYer may not be aware of. The coping of? the ornate section of the skirting is the first (most inexperienced DIYers would just cut two 45 angles and nail them together) and the clout at the bottom of the plasterboard sheeting is the other. These two together make for a very nice internal corner.

So what's the " ...
By: MrTrda. on 22 Feb 12, 02:58:15
So what's the "secret"??? ? Explaining to people what a coping saw is used for?

hello?
By: STONEMAKERCANADA. on 07 Feb 12, 17:23:45
hello?

excellent video ...
By: MrElectrodesign. on 26 Jan 12, 04:42:21
excellent video and? some very good tips , much appreciated mate

Thank you, thank ...
By: ohdrdrdr. on 19 Jan 12, 20:31:02
Thank you, thank you, and thank you. I read about cutting the curved outline with a coping saw. My reaction was : Wha????? This video makes it look easy and logical.? Hope it works out in my real life attempts.

If your doing your ...
By: Thereminator101. on 04 Jan 12, 23:00:28
If your doing your own home (or a custom-home job) its probably worth coping the corners,because it will hide the joint better.On all of the Hotels Ive been on we 45 the corners(on base)because its much faster and I usually prop the bottom out and glue them.You get good at the 45's if you do enuff,and every production dollar counts for the bigger contracts,even on? the five star hotels.

legend!?
By: StephJoRoryInnes. on 29 Nov 11, 19:23:19
legend!?

@vadimyerzakovich ...
By: shaneconlan1. on 28 Nov 11, 00:26:50
@vadimyerzakovich Come on mate, you can't leave us hanging. What's your secret? Just in relation to the time it takes to do a coped corner, it takes no time at all after you? have done a few of them. It really isn't an issue. Cheers.

Thank you!! ?
By: leady5. on 20 Nov 11, 16:02:30
Thank you!! ?

Brilliant, ...
By: MrEggy101. on 11 Nov 11, 23:17:24
Brilliant, informative and entertaining video Uncle Knackers. I'm doing? most of the whole of the downstairs of my house this weekend and I'm grateful for this.

You can also use ...
By: shaneconlan1. on 17 Sep 11, 21:38:31
You can also use screws or nails to attach the timber and skirting board as long as you screw or nail above the? damp course line.

Thanks for the ...
By: shaneconlan1. on 17 Sep 11, 11:16:22
Thanks for the comment. In regard to the dpc (l'm assuming you are referring to a damp proof course), you are correct. Any penetration of that barrier will affect the integrity of the product. Packing the wall out with timber will work but you may have to use a? good quality construction adhesive to bond it to the wall before you nail the skirting board to it. Make sure that the nails you use aren't that long that they go right through the piece of timber that you have glued to the wall.

loved your vid ...
By: debstarcrazy. on 17 Sep 11, 07:12:40
loved your vid thanks! Now can you tell me how to fit it square after having a chemical dpc fitted, where the plaster stops at the top of the first row of bricks? Iassume? I need to pack behind it with some wood and screw into the bricks? Wont that affect the dpc?

Easy Baseboard Inside Corner
Posted by: HomeRemodelWorkshop

Video duration: 91 seconds
Global video hits: 248437

Carpentry skill for cutting an inside corner of baseboards.remodelin g renovation repair do it yourself! baseboard installation

Related: bob, schmidt, home, remodel, workshop, base, baseboard, board, trim, molding, installation, skirtboard, skirting, boards, improvement

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

caulking is my best ...
By: MrTinflo. on 11 Apr 12, 00:46:18
caulking is my best friend!!!?

why do these scab ...
By: dewaltcarp. on 18 Feb 12, 03:54:17
why do these scab carps even post? because it lets carpenters as good as the? video no how good they really are

Just coped some ...
By: copperheadharley. on 15 Feb 12, 05:56:27
Just coped some trim today. Looks much better than? two 45s.

OH.... that is ...
By: tommmmmer. on 23 Nov 11, 20:48:21
OH.... that is where i was going wrong... i wasn't? 45ing it to start with :/

A tip I got from a ...
By: beransom. on 06 Nov 11, 19:14:30
A tip I got from a pro finish carpenter is this: Use a small square against the baseboard to see? how far out of square it is when pushed against the wall at the bottom (due to the drywall not going all the way to the floor). Using the gap, that is shown by the square at the bottom, cut a piece of shim stock the same size. Drop this in behind the baseboard and recheck for square and nail in place. No matter what you will always have a square base for your next piece of base to but up against.

He makes is look so ...
By: ebyun84. on 29 Aug 11, 04:14:48
He makes is look so easy.?

Well? said.+++Bob
By: HomeRemodelWorkshop. on 16 Jul 11, 02:17:06
Well? said.+++Bob

I don't think I saw ...
By: jeffpicks. on 16 Jul 11, 00:45:27
I don't think I saw an answer to the question "Why not just cut two 45� and be done with it?" Answer: actually, TWO reasons come to mind, and there may be more. FIRST, most corners aren't 90�.. BAD FIT, need the putty and paint. SECOND: No matter how well you try to get the angle set, when you NAIL THE BOARD IN PLACE the? miter moves apart. With this method shown you nail the butt piece first, slam the sharp edge of the cope into place, and nail to wall. No movement that opens the joint.

Nice quick neat ...
By: davbay100. on 27 Jun 11, 09:42:47
Nice quick neat video? cheers.

Nice job. What if ...
By: Theshuttersguy. on 24 May 11, 05:23:33
Nice job. What if you could buy the molding from the factory already coped on? one end?

BRAVO!! but,dammit! ...
By: ClintL63. on 26 Jan 11, 04:30:28
BRAVO!! but,dammit! you're? giving away all my secrets!

that's why you ...
By: gungfuryan. on 16 Jan 11, 02:22:04
that's why you leave a sharp edge and hammer it in. it fixes itself and with the compressed bit at the end,? if there is expansion & contraction it still stays tight

it's actually ...
By: gungfuryan. on 16 Jan 11, 02:20:31
it's actually called 'coping'?

the mitre avoids ...
By: gungfuryan. on 16 Jan 11, 02:20:14
the mitre avoids having to scribe. coping is quicker, easier and just as good? in the end

Great help and I ...
By: billeybop. on 14 Sep 10, 00:39:35
Great help and I appreciate your skill! I will go practice now,? Thanks!

Why not just ...
By: lanya100. on 07 Aug 10, 02:15:12
Why not just measure the corner, figure its complement, divide by two and miter 'em. If that fails, at TS&F (Trip Stumble and Fall) Construction's finish carpentry division, better known as the Not Read For Stain Grade Players, the motto is, "Putty and Paint Make It What It Ain't." Probably best not to listen to me, I cut all of my crown "on the flat" and? NEVER miter an inside corner. Haven't had a visible crack (YEARS later) yet.

this method is ...
By: andrewbobbin. on 31 Jul 10, 20:39:17
this method is called scribing and is the RIGHT way to do it... mitre internal cuts are for D.I.Y? only

Why on earth are ...
By: shad28960. on 13 Apr 10, 18:27:57
Why on earth are you going to the trouble of cutting a mitre for the inside corner? All you? have to do is scribe the board using a small section of board laid against the back of the board to be cut and use a coping saw to cut the profile. Basic.

with the 3 1/4" ...
By: SuperDanksta. on 15 Mar 10, 00:15:58
with the 3 1/4" base you can flip itand cut the straight art with the saw so you don't have to cope the? whole thing

Joiner tip. Always ...
By: grip2010dc. on 23 Nov 09, 10:08:22
Joiner tip. Always fix the first skirting back to the wall Before attempting the fit the? second skirting as the scribe may not fit after. Sometimes the wall is not plumb or the floor is not level and this is when a true cut in not right .

Are you serious? ...
By: xPilotxHellfire. on 16 Nov 09, 01:23:30
Are you serious? Turn your Mitre saw to the opposite angle of the inside... For? an external 45 degree angle..

Lets hope thats a ...
By: HomeRemodelWorkshop. on 12 Oct 09, 21:42:30
Lets hope thats a good thing Thanks for? watching! Bob

nice cut, i am ...
By: wlc2382. on 12 Oct 09, 18:16:27
nice cut, i am getting as good as? you thanks for the help

Very helpful. ? ...
By: samlesher. on 01 Oct 09, 22:50:32
Very helpful. ? You're awesome!

Why not cut both ...
By: 3asa3isso. on 06 Sep 09, 10:21:37
Why not cut both side? on a 45?

BASEBOARD INSTALLATION TIP
Posted by: HomeRemodelWorkshop

Video duration: 138 seconds
Global video hits: 86616

BOB SCHMIDT SHOWS YOU A SHORtCUT WHEN IT COMES TO COPING INSIDE CORNERS WHEN INSTALLING BASEBOARDS SKIRTBOARDS AND OTHER TRIM WITH FLAT AREAS ON THEM

Related: trim, moldings, moulding, base, baseboard, board, molding, installation, cutting, easy, mitre, box, repair, wood, construction

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

God bless you for ...
By: realterm123. on 14 Mar 12, 22:25:13
God bless you for sharing.?

Most people? I know ...
By: HotRodSixString. on 01 Mar 12, 02:11:26
Most people? I know make the cut with the miter saw first and then finish it up with the coping saw

thanks for the tip, ...
By: 123milkbone. on 31 Jan 12, 06:24:46
thanks for the tip,,,,,, but seems like you, and understand you have done it a lot more than i, but it took you 20 seconds to do it by hand with hand tools, at least make it look a little harder to do by hand, ie. reason to run to the? miter saw,

Good luck with a ...
By: ILuffYewwChris123. on 28 Aug 11, 13:36:58
Good luck with a jigsaw on pre finished wood. And the "unless you wanna take forever on a house this video is for you" Guy is a perfect example of the get it done fast, quality doesn't count mentality of our industry. Still haven't met? anyone who uses a jigsaw or an angle grinder (WTF?) Who's copes turn out as good as with a coping saw and a back cut. Keep it up Bob. Show em the right way....let em take the shortcuts on their own.

Thanks Bob, very ...
By: 123HURST. on 22 Jul 11, 18:09:11
Thanks Bob, very useful video.?

why??
By: HardFii. on 25 Jun 11, 21:10:43
why??

Interesting, looks ...
By: HomeRemodelWorkshop. on 27 Feb 11, 13:43:09
Interesting, looks a bit dangerous for the novice or beginner. There is a table mount guide that looks a bit safer not as? fast thou.+++Bob

I've seen the ...
By: inbetweentheday. on 27 Feb 11, 06:01:11
I've seen the collen's coping foot you attach to a jigsaw.? Check it out it's interesting on coping.

@fishnriver, I ...
By: snakyjake1. on 02 Feb 11, 05:04:39
@fishnriver, I imagine this would work if you? didn't have rounded profiles.

Hey Bob, don't ...
By: kevinalavarezsr2. on 30 Jan 11, 18:41:48
Hey Bob, don't worry about your critics....they tend to display their? stupidity and lack of communication skills by using colorful language to draw attention. In the end they can't produce the goods to match their mouth. Keep up the great work!!

Your Doing a fine ...
By: plexsus. on 02 Jan 11, 15:30:59
Your Doing a fine job Bob....keep it? up.

nice video thanks ...
By: grench2o6. on 07 Dec 10, 23:01:54
nice video thanks for the tip? ill try it out!

Thanks for the tip ...
By: jhart1945. on 20 Jul 10, 18:14:19
Thanks for the tip Bob. I use it and it works great. Like you, I am always looking? for better/faster ways to do things so i also wish Hellrisepl1 would share his method instead of badmouthing yours!

Why use a coping ...
By: blzbass. on 18 Jul 10, 14:15:13
Why use a coping saw? when you can use an electric jig saw?

you are what we ...
By: holywar911. on 07 Jul 10, 04:50:42
you are what we call "mr? know it all"

Thanks Bob for all ...
By: zipdrive011. on 29 Jun 10, 06:52:14
Thanks Bob for all the tips. For those who? don't appreciate these tips, you don't have to leave some colorful comments too.

Ok I'll bite. If ...
By: HomeRemodelWorkshop. on 23 Jun 10, 20:35:18
Ok I'll bite. If you could leave us a brief? explanation on the far quicker and quality improved method I am sure we would all love to hear it. If you could leave the colorful language out it would be appreciated since we don't know who may be reading these comments Thanks+++Bob

this shit makes no ...
By: hellriserpl1. on 23 Jun 10, 17:38:57
this shit makes no sense, i did a lot of? base, and this is not how u do it, but if u want to spend 10 years to do one house of base this vid is for u.

Bob; sorry I don't ...
By: fishnriver. on 29 Oct 09, 17:41:52
Bob; sorry I don't have the means to record a video and post it but I'll see if I can find a source and post? it in the near future.

I would love to see ...
By: HomeRemodelWorkshop. on 29 Oct 09, 09:32:33
I would love to see that,do you have a video? of that on your channel?+++Bob

After you make the ...
By: fishnriver. on 29 Oct 09, 03:48:10
After you make the straight cut hold the base firm remove the pc up to where the cut ends, then drop the running blade back down to where you? stopped and begine to SLOWLEY slide the base to the left and very gently lower the saw as the base moves and follow the profile. No need for a cope saw, just touch up a little with a rasp. Been doing this for years. Takes a steady hand and good eye correlation.

Awsome video... ...
By: blackpearlhomes. on 21 Oct 09, 06:58:45
Awsome video...gonna try this out? tomorrow on a basement instead of all those pesky 45's

I always learn ...
By: gahanwilson. on 24 May 09, 14:30:56
I always learn something from your videos. Keep up the good work!?

I'm still getting ...
By: 5150hs. on 01 Apr 09, 06:32:26
I'm still getting this technique down. Coping on MDF is a little harder. Unless... you have another helpful idea for us budget strapped DIY? people who us MDF? Thanks for your great videos.

Ever doing a thing ...
By: gwezeemichelle. on 27 Mar 09, 22:20:38
Ever doing a thing on shingling the? roof from scratch to finish. I would love to learn it. thanks

Painting Baseboard
Posted by: PaintSourceNetwork

Video duration: 167 seconds
Global video hits: 47295

Easy way to paint baseboards while protecting carpet.

Related: painting base board, painting trim

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

Thank you. It all ...
By: 1971SuperLead. on 23 Jun 11, 16:46:14
Thank you. It all makes sense now after I painted my entire home! lol I used wide packing tape on my carpet up against and underneath the baseboards. I used a 3 inch? wide plastic puddy knife to get the tape to go underneath the baseboards. It worked great.

: Better to email ...
By: PaintSourceNetwork. on 23 Jun 11, 16:17:14
: Better to email us through our website. That question has no short? answer. We are just demonstrating here one method to consider for painting trim.

: We had not ...
By: PaintSourceNetwork. on 23 Jun 11, 16:14:13
: We had not painted walls at that point. We plan to tape the trim before painting walls, so? the bit of trim paint up on the wall gives a bit more paint film over the caulk, and gives us straighter cleaner lines where wall meets trim. If walls are painted before trim (not our choice), we would neatly cut in the trim to wall. We wanted to show 3 things. 1. Place paint in middle. 2. Spread paint to edges. 3. Smooth paint sweeping backward and lifting brush with a light stroke.

Would this work to ...
By: missgigglygirl. on 23 Jun 11, 05:20:36
Would this work to paint? natural wood baseboards white? Would I prime it first?

Your videos seem ...
By: DEBROXDEBROX. on 09 Jun 11, 18:45:00
Your videos seem very professional. Others fool you into thinking, "This looks right" until you look down and see a bunch of negative comments from? the knowledgeable. Your videos are the only ones without mass negative comments. Thanks.

Why? didn't you ...
By: 1971SuperLead. on 11 Dec 10, 17:34:09
Why? didn't you tape the wall for a straighter line?

: Our techniques ...
By: PaintSourceNetwork. on 11 Dec 10, 15:56:51
: Our techniques are designed for the inexperienced painter. With tape protecting the carpet, it also "holds down the carpet, many times, keeping the carpet from springing back into the wet paint. Why take a chance on a drop cloth rubbing the paint, or paint dripping on the carpet. The technique we show for taping the baseboard is part of a process that eliminates the typical "cut in" for both walls and trim, and gives? perfectly straight lines.

You taped the ...
By: 1971SuperLead. on 03 Dec 10, 01:38:55
You taped the carpet??

Great? tip, thanks!
By: BrotherOrchid. on 19 Sep 10, 19:46:25
Great? tip, thanks!

Painting the Baseboards
Posted by: BenjaminMoorePaints

Video duration: 107 seconds
Global video hits: 14148

This brief instructional video gives you an inside look at the best techniques for painting the baseboards in your home!

Related: benjamin moore, how-to, baseboards, paint

Display Video Comments | Hide Video Comments | Add Comment

USING AIR NAILERS FOR CABINET TRIM, BASEBOARD & CASING
Posted by: HomeRemodelWorkshop

Video duration: 237 seconds
Global video hits: 38682

BOB SCHMIDT SHOWS YOU BASIC TIPS ABOUT THE USE OF TRIM AIR NAILERS WHILE WORKING ON YOUR HOME REMODEL PROJECTS SUCH AS KITCHEN SPECIALTY TRIMS AND COMMON MOULDINGS IN YOUR HOUSE.RENOVATIONS IMPROVEMENTS WOODWORKING REPAIR

Related: chairail, remodeling, workshop, safety, baseboards, casings, cabinets, nailer, types, uses, crown, flooring, tools, tool, woodwork, food, home

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

I bought a CH brad ...
By: PotatoGunsRule. on 28 Nov 11, 17:20:15
I bought a CH brad nailer....18 guage...I want to put on? floor trim onto my MDF kitchen cabinets....

Thanks for the ...
By: ak99372. on 29 May 11, 07:19:15
Thanks for the great video. Do you need to oil these tools??

You are? awesome to ...
By: clhodg. on 21 Nov 10, 01:36:29
You are? awesome to share this info! Thank you!!

Yes as a matter of ...
By: HomeRemodelWorkshop. on 31 Oct 10, 21:43:01
Yes as a matter of safety most guns will not shoot unless the? head of the nailer is pressed against work surface+++Bob

that u-turn nail ...
By: signupsigma. on 31 Oct 10, 20:02:24
that u-turn nail sounds dangerous. Thanks for the safety tip. But is there a choice? Regardless of nail lenght, don't you have? to put the gun head right up to the board?

I generally only ...
By: HomeRemodelWorkshop. on 09 Aug 10, 19:29:34
I generally only use it with small accent moldings.+++Bob? Alot of the time the holes are so small the nail holes are hard to find to fill.

Newest subscriber.. ...
By: mission762008. on 09 Aug 10, 07:23:04
Newest subscriber..thanks for the videos. Wil come in helpful as I just bought a new house. Quick question, my hobby is woodworking and furniture making..so with the new house I was thinking about making? my own cherry or mahogany moldings for some of the rooms. Would the micronailer be ok to hang trim molding, or would the weight be too much? I've seen those micronailers..it would be so much easier to get rid of those holes in expensive woods rather then use the regular nailers!!.

Boom! They got a ...
By: humangod. on 05 Dec 09, 17:59:23
Boom! They got a nail in them. ha.? that was funny.

Very helpful and a ...
By: mellypage. on 17 Oct 09, 00:10:19
Very helpful and a joy to watch! The enthusiasm is? infectious!

Love your video's. ...
By: 5150hs. on 28 Feb 09, 07:49:14
Love your video's. Very helpful tips.? Thanks.

hit it in the stud?
By: vitalikdze1887. on 14 Oct 08, 23:21:02
hit it in the stud?

Good tips - thanks ...
By: cjbates123. on 23 Dec 07, 17:11:29
Good tips - thanks a? lot!

Great? thanks.
By: redynamic. on 10 Sep 07, 03:18:31
Great? thanks.

Can you show us how ...
By: wbradd3797. on 13 Mar 07, 16:29:57
Can you show us how to properly hang cabinets? That's a project I will be doing this summer and some pointers? from a pro would be helpful.

Spraying door jambs, baseboards, doors, and windows.
Posted by: idahopainters

Video duration: 343 seconds
Global video hits: 6403

Video shots on spraying interior trim work. Techniques spraying door jambs, window trim, baseboards, and doors using a Titan airless sprayer. www.idahopainter.com www.facebook.com www.twitter.com

Related: how to use and airless sprayer, how to spray trim, how to spray woodwork, painting trim, how to paint a door, painting doors, proper way to paint a door, chris berry, b&k painting, www.bnkpainting.com, bk painting, christopher berry, how to spray a window, how to spray with an airless, painting window trim, airless sprayers, how to operate a graco sprayer, how to spray window trim, proper airless spray technique, paint, paints, painting, painter, painted

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

I have never ...
By: idahopainters. on 01 May 12, 05:39:56
I have never worried about getting over? spray on the walls. You can never tell. We use satin on the walls semi gloss on the trim. We mask the trim off with plastic before spraying the walls.

We use? it for ...
By: idahopainters. on 01 May 12, 05:16:59
We use? it for everything.

how helpful is your ...
By: hardcoremofo. on 20 Apr 12, 04:32:59
how helpful is your masking tape dispenser? Do you use it for all windows and doors? ?

I noticed that you ...
By: allen52965. on 12 Apr 12, 05:54:04
I noticed that you didn't have any cover around? the door frame to avoid painting the same paint on the walls. I assume that you are going to use a different paint on the wall and that you will cover the door frame once you start spraying on the wall, am I correct. Also, you don't have any problem with getting spray paint around the frames of the windows because your cover is only about a foot wide. Is the technique on keeping the pressure low, or it's a skill you developed over the years?

Prime and paint two ...
By: idahopainters. on 11 Jan 12, 19:31:13
Prime and paint two coats on trim first. If ceiling are a? different color then walls, paint walls first. Then drop with plastic and mask ceiling lines and spray ceilings.

Hey Chris. Great ...
By: bobjoesmith. on 07 Jan 12, 00:30:46
Hey Chris. Great vid(s) thanks a ton. I have a question if you got a second. Just bought a rental home that is dripping nicotine. Washed walls and ceiling w/ ammonia/water. Yuck. Going? to spay the entire home w/ BIN first then top coat. Question.. what is your reco for the order of this process. Walls, trim, ceiling? New flooring going down so going to us Graco sprayer and 515 / 311 tips per your video reco.. Thank in advance.

Joaodisco, the ...
By: idahopainters. on 05 Jan 12, 17:36:17
Joaodisco, the language is broken up? so I cannot read it to respond.

Ola friend I am ...
By: JOAODISCO. on 01 Jan 12, 23:03:22
Ola friend I am Brazilian e I liked them its works with painting and mainly with this type of that is here new mechanism in esprey still more I quardando a money to buy this a similar schemes or its. good I would like to know the income for liter of ink? and that types of ink would give to apricar with it. Grateful quardo reply JO�O.

Acryshield semi ...
By: idahopainters. on 16 Dec 11, 06:09:45
Acryshield semi gloss for trim and doors. Back brushing trim and doors is the dumbest thing ever. I cannot believe they said that. that defeats the whole purpose of spraying the trim and attempting to get an automobile finish.?

thanks for a great ...
By: GatorBrewer99. on 15 Dec 11, 12:03:09
thanks for a great series of videos - been very helpful. what PSI did you use for the doors/base? Also,? Sherwin Williams recommended backbrushing the doors/windows but I see you did not - do you not recommend? Finally, if painting 16ft uninstalled base/crown prior to installation, would you spray the length walking up and down parallel to the boards, or perpendicular?

Door Rack Painter. ...
By: doorrackpainter. on 30 Nov 11, 06:56:43
Door Rack Painter. com? Paint & Store Regular Doors & Cabinet Doors On Both Sides. Store Painted Baseboards And Other Items 20" Long In This Multiuse System

We only use water ...
By: idahopainters. on 24 Nov 11, 17:34:02
We only use water based paints. Oil based products are being fazed? out due to strict environmental regulations.

Hi, great? video ...
By: MrRobgardner. on 23 Nov 11, 20:38:44
Hi, great? video mate. I'm a professional decorator from the UK, just about to buy my 1st airless sprayer. Are you using a water based or oil based paint ?

you are a real ...
By: TrojanWarrior74. on 21 Nov 11, 12:37:48
you are a real perfectionist , well done mate , your a? dying breed , love your vids

Like your work?
By: davedeandec. on 21 Nov 11, 10:48:58
Like your work?

Baseboard Heater Covers, Easy to Install Baseboard Covers
Posted by: PexSupply

Video duration: 74 seconds
Global video hits: 44725

Easy to Install Baseboard Covers

Related: baseboard, heat, heaters, install, covers, home, improvement, heating, supplies

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

For hydronic ...
By: matics19. on 03 Mar 12, 21:15:57
For hydronic heaters, right? Electric heaters would produce significantly higher temperatures so the currents behave differently. My experience is in electric baseboards, hydronics I've only done minor work? with.

Convection air ...
By: PexSupply. on 02 Mar 12, 19:03:27
Convection air currents move through Baseboarders in the identical fashion as without? Baseboarders installed. Efficiency is not negatively affected. The "chimney effect" describes how the cover allows the heated air to escape while ensuring cooler air from below has a clear, unobstructed path to come into contact with the element. Baseboarders are tested in controlled conditions and have proven to have the same efficiency levels as standard baseboard heater covers.

The convection in ...
By: matics19. on 01 Mar 12, 19:45:23
The convection in the perforated design will be less efficient. It is correct to state that the airflow would be similar, but the turbluence would be greater through the perforations and the air would not rise as high along the wall. This won't make? a noticeable difference in most smaller rooms or hallways, though.

This is simply not ...
By: justcurious4. on 24 Jul 11, 04:16:48
This is simply not true. The perforated steel one-piece design will push the same amount of air through as the solid front panel design will. Both designs do not have any obstructions at the floor level and both will accelerate the convection air currents when they come into contact with the heating element. I've also heard that the? perforated design is MORE efficient than the old ugly design.

It will also keep ...
By: frankt04. on 08 Dec 10, 17:05:41
It will also keep crayons and plastic toys out. Only problem I see is if you? did a smoke test between the two designs you would see there is better airflow with the traditional cover due to the front plate. Without it there cannot be convection= reduced efficiency of an already inefficient unit in the case of electric baseboard. I know that wasn't electric but it still works on convection.

These will keep ...
By: dwightinutah. on 28 Mar 10, 02:35:21
These will keep children's fingers out of the innards of the heater, but it will not necessarily keep? them from being burned.

These? are OK for a ...
By: lrd9999. on 28 Dec 09, 20:10:35
These? are OK for a room with a thermostat, if you like the new look. But in a bedroom that "piggybacks" off a heat zone without controlling it, you need the damper flap to adjust the heat output, unless you have a shutoff valve.

how to fit base boards
Posted by: dimboolaboy

Video duration: 131 seconds
Global video hits: 33252

more free movies at www.howtobuildahouse .com.au

Related: how, to, buid, house, diy, home, improvements

Display Video Comments | Hide Video Comments | Add Comment

House Cleaning - Baseboards
Posted by: monkeyseevideos

Video duration: 198 seconds
Global video hits: 9993

Related: N/A

Display Video Comments | Hide Video Comments | Add Comment

Slant/Fin Baseboard Installation
Posted by: slantfincorp

Video duration: 163 seconds
Global video hits: 32705

The highest quality baseboard you can install in your home.

Related: baseboard, hydronics, home, improvements, contractors, installing, heating, comfort, plumbers, construction, technology, slantfin, slant, fin, contractor, boilers, high, efficiency, green, plumbing, saving, money

Display Video Comments | Hide Video Comments | Add Comment

how to install base board
Posted by: blakech

Video duration: 201 seconds
Global video hits: 113070

how to install base board by RenoTube.ca

Related: renotube.ca, reno, tube, construction, hardwood, drywall, insulate, lapse, blake, darren, winckle, moulding, renovation, live

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

Inside 45 degree ...
By: varmintslayer311. on 27 Jun 11, 07:28:12
Inside 45 degree cuts separate through the? seasons. That is why you Cope them. How does it feel to know you have misinformed nearly 100000 people? Hack.

Just wanna say lol ...
By: neviazov1. on 04 Oct 10, 05:14:09
Just wanna say lol but 5? stars

sound? is crap
By: scottiehypnosis01. on 06 Aug 10, 12:09:32
sound? is crap

Thank you very much ...
By: zgele77. on 04 Apr 10, 04:49:29
Thank you very much for the video The issue I have is that my wall is a concrete (double brick). How do I fix it to the wall, I can't? use nails only can I?? Thank you

I? guess it was ...
By: KoreyBigchild. on 18 Feb 10, 01:58:04
I? guess it was considered finished LOL

can you hide a wire ...
By: RideRideRide4Life. on 10 Jan 10, 21:40:45
can you hide a wire behind it?

what??
By: Bobtheicon. on 24 Dec 09, 17:09:59
what??

hey blake you ...
By: bubbzontario29. on 21 Nov 09, 04:30:39
hey blake you should put the drywall up? first you dick

thanks!! gracias?
By: marc122979. on 17 Oct 09, 18:12:03
thanks!! gracias?

Cant this? idiot ...
By: MrWilmas. on 13 Oct 09, 19:51:33
Cant this? idiot talk louder.............

Why do people have ...
By: 28SNaKeS. on 30 Aug 09, 17:31:12
Why do people have to be such jerks. I heard him perfectly fine. The quality of the audio isn't up to par, but you can hear what he's saying just fine. What are you all, 14? Thank you, Blake for this video. It helps? A LOT.

Wow...this is ...
By: hbchman. on 29 Jul 09, 21:22:13
Wow...this is really done old-school. ? Old school??? I mean old-testament!!

not that good, ...
By: emailcab. on 09 Mar 09, 23:13:47
not that good, doesn't explain where nails have to nailed to (drywall only).......?

I'd love to know ...
By: tigertown99. on 01 Feb 09, 00:45:50
I'd love to know what you're? saying

can you speak ...
By: stitchy66. on 10 Dec 08, 00:45:37
can you speak louder? i can't hear you.?

what about the ...
By: pythonflying. on 14 Oct 08, 01:31:08
what about the silicone, do? I just run a bead on top?

please? re-record ...
By: mbcline. on 19 May 08, 20:00:17
please? re-record with normal volume levels

Very? helpful for ...
By: ciclon75. on 25 Apr 08, 13:29:08
Very? helpful for me this video , thanks !

I? can hardly hear ...
By: guitaristforChrist. on 08 Apr 08, 15:55:30
I? can hardly hear this guy either!!

someone with a lot ...
By: vicksurdaddy. on 17 Mar 08, 08:31:42
someone with a lot of time, patience, and a fear of power tools...or...this video was? filmed in 1937

Damn, must have ...
By: Howlnwoof. on 12 Mar 08, 19:46:26
Damn, must have been all that loud Rock and Roll I listened to as a kid...can't hear? a thing..

Who uses miter ...
By: Damienr6. on 09 Jan 08, 04:03:37
Who uses miter boxes anymore? And for that matter, why? would you renovate an entire house without a compressor and some pneumatic nail guns?

No sound.?
By: cuffeea. on 21 Jul 07, 17:18:38
No sound.?

Concrete Floors Baseboards & Transitions
Posted by: cntelevision

Video duration: 211 seconds
Global video hits: 22199

Visit www.concretenetwork. com for more concrete floor videos. Concrete floor video on how to install baseboards and transitions at the proper height to adjust for the new concrete flooring. Baseboards may need to be cut to the height of the new flooring. Tips on what to ask your floor contractor.

Related: concrete, floors, video, floor, baseboards, transitions

Display Video Comments | Hide Video Comments | Add Comment

Cleaning Kitchens : How to Clean Baseboards
Posted by: eHow

Video duration: 78 seconds
Global video hits: 4245

Clean baseboards by vacuuming up dust and then scrubbing with a toothbrush and soapy water. Find out more about cleaning baseboards in this free video from a professional home organizer about cleaning kitchens. Expert: Ann Myrick Bio: Since 1997, Ann Myrick has been a professional decorator, house cleaner, home organizer and planner. Filmmaker: Tim Brown

Related: cleaning kitchen, housekeeping, housecleaning, microwaves, kitchen appliances, coffeepots, ovens

Display Video Comments | Hide Video Comments | Add Comment

Installing wood baseboard to a concrete column
Posted by: VideoJoeKnows

Video duration: 159 seconds
Global video hits: 3857

Installing wood baseboard to a concrete column......is easy....when you know how. Don't sweat concrete columns as you're just going to have to do "this" when installing the baseboard. I know you're not use to installing wood baseboard this way, but get use to it when working around concrete columns. Watch as "joe" gets ready to install wood baseboard around a concrete column.

Related: how to install baseboard, how to install base board, how to install baseboad, how to install basebored, how to install basebord, how to install basebaord, videojoeknows, instructional video content, how to install base boad, how to install base bored, how to install base bord, how to install base baord, how to install wood baseboards, how to install base

Display Video Comments | Hide Video Comments | Add Comment

Latest comments made on this video:

Awesome! I'm glad ...
By: VideoJoeKnows. on 25 Jan 12, 06:46:19
Awesome! I'm glad you were able to check out? these videos before doing your project. Good luck. Joe :0

man I am just about ...
By: BlueToad2222. on 25 Jan 12, 04:39:57
man I am just about to start a trim job? and all these videos are perfect!

That might be fine ...
By: VideoJoeKnows. on 04 Sep 11, 04:02:39
That might be fine for someone of your experience? but for someone who is not really a carpenter, this way is way more easy for them......especially when the column is not perfectly plumb & square. Thanks for your comments. I appreciate it. Joe :0

By the time do all ...
By: CarpenteryDIY. on 04 Sep 11, 03:39:23
By the time do all that with liquid nail. One can measure nail it together on a bench, add a bit of PL stick it to the wall prime paint and forget about? this headache that you are showing

Sometimes "joe" ...
By: VideoJoeKnows. on 21 Apr 11, 06:10:20
Sometimes "joe" talks more so you can learn more. You can learn by someone doing something &? also by what someone is saying....as in this case. "Joe's" got plenty other videos where he is doing something for you. Have a particular question on something you don't see on his channel?....tell him about it. Thanks for checking out "joe". :0

so do it, stop? ...
By: superbagner. on 21 Apr 11, 04:56:42
so do it, stop? talking and show it. damn

You are not an ...
By: VideoJoeKnows. on 07 Aug 10, 08:02:12
You are not an idiot. Once you start installing baseboard around corners, you will quickly get the hang of which angle you need, & how to fit the corner together. It's also important to use a wood rasp to clean up any overlapping edges, before caulking any minor gaps upon completing your corner(s). After you have your corner together, you can now apply finish paint to it? & wahlah..done. Thank you for sending me your comments. I always like to hear from my viewers. Keep watching. Joe :0

Thanks. I'm an ...
By: Joxman2k. on 07 Aug 10, 05:22:06
Thanks. I'm an idiot so I din't realize that? certain angles are common, well I did know that you just divide the angle you want, but it looks pretty complicated with the multiple angles. :P

I don't generally ...
By: VideoJoeKnows. on 07 Aug 10, 04:38:48
I don't generally use any tools to figure out the angles as most angles are either 90 degrees, 45 degrees, or half of a 45 degree (22.5 degrees) when working with baseboard install. If a wall is not an exact 90 degree or 45 degree angle, I can usually fudge it a little or trim? it a bit to make it fit. if you have a different angle, you could cut a few test pieces to check out the angle before cutting your actual piece. Thanks for your questions. Joe :0

How do you ...
By: Joxman2k. on 07 Aug 10, 04:27:28
How do you determine the miter angles? What tools are best? :P ?

Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Scrapbooking Related Videos

Scrapbooking - Scrapbook Ideas - Online Scrapbooking - Cheap Scrapbooking - Online Scrapbook - Scrapbooks Etc - Scrapbook Software - Scrapbook Storage - Scrapbooking Downloads - Scrapbook Titles - Scrapbook Maker - Scrapbook Convention - Scrapbook Rooms - Scrapbooking Blogs

You like it? Share it!

Social Bookmarking

"4 Belly Fat Mistakes"
Controversial free video:
Do you make these
4 "dumb" diet mistakes?
5TipsToLoseStomachFat.com

Baseboards video compilations

Scrapbooking Related Videos

Sponsors

"Amazing Scrapbooking Secrets Brings Special Family Moments Back To Life . . . Transforming a Mountain of Photos into Raw Teary-Eyed Emotion."

"Oops, Can't Think of Anything to Write on Your Scrapbook Pages? 5,000 Scrapbook Titles & Quotes is the PERFECT Solution!"